Specification

Air Consumption
Approximately 5.0 cfm (143 l/min)

Air Supply
90psi/6 bar, dry, uncontaminated.

Controls
Sensor.
PLC.
Host print.

Cycle Rate
Up to 120 pallets per hour. Print and apply time for printing and applying a front and side label approximately 14 seconds.

Electrical
115/230V, 50-60Hz, 1ph, 350W.

Environment
CE certified, including hazard analysis.
Operating environment of 39° to 104°F (4° to 40°C); Active heated enviromental cover optional - 5° to 104°F (-15° to 40°C).
Relative humidity 10-90% (non-condensing).
Noise level not to exceed 80 dB(A).

Label Size
8.26"L x 6"W (210mmL x 150mmW).

Print Specs
More than 1,000 font styles available including non-Roman characters, resident, downloadable and scalable.
TrueType fonts available as bitmap data.
Graphics downloaded through use of optional ComposerT software.
Bar codes Interleaved 2 of 5, (ITF 14), code 39,code 128, EAN 8, EAN 13, UPC A, UPC E, EAN 128, UCC 128, PDF 417, QR Code, DataMatrix

Sensors
Active pack detection sensor for variable pack configurations.
Pad home sensor, with fault warning to prevent applicator damage.
Label gap sensor standard.
Foil detect sensor standard.
Low label warning sensor standard.
Safety stop circuit.

Supplies
MARKEM recommended spares. MARKEM thermal transfer and direct thermal labels.
MARKEM thermal transfer foil.
MARKEM printhead materials.
Label stock inside wound.
Label roll outside diameter 12" (300mm).
Label roll inside diameter 3" (75mm).
Recommended label gap 0.118" (3mm).
Outside inked ribbon.
Print ribbon length 1400' (450m).
Print ribbon core diameter 1" (25mm).

User Interface
On-board label database (no dedicated PC required).
Full on-screen fault diagnosis.
Backlit LCD display.
Wipe-clean industrial keypanel.
Multi-language support.
Label/product counter.
Left or right hand options allow easy operator access.

Print WS Options
6" (152mm) 200dpi printhead - 6"/sec. (150mm/s).

Apply
Flexible and compliant tamp label applicator.
Front, Front/side, side, front/side/rear, rear/side, rear.
Active pack detection sensor for variable pack configurations.
500mm or 750mm (29.53") stroke lengths

Options
3-color status beacon.
Label verification scanner to check barcode, barcode data, and label has been applied. Provides reject output and Cimjet can be interlocked with conveyor.
Product identification scanner to select products.
Remote operator interface pod.
Enviromental Cover.
Active enviromental cover.

Print Area
Maximum print area 152mm x 400mm with 152mm printhead

Print Speed
Up to 120 pallets/hour (2 labels per pallet)

Label Range
Max: 8.26"L x 6"W (210mmL x 150mmW).
Min: 2" x 2" (50mm x 50mm).
Handles A5 and A6 labels.

Standard Label Pad Sizes or Applicator Range
8.26"L x 6"W (210mmL x 150mmW). A5 (Pads can handle labels up to the size indicated. Labels must cover the main % of the pad. Custom pads are available as options.

Dimensions
3.9 ft. wide x 3.6 ft. deep x 5.6 ft high (1.2m x 1.1m x 1.7m)

Communications
RS232/422/485 serial interface (2,400-57,600 baud).
Ethernet interface optional.
Network up to 62 units using optional CimControlT software.

Pack Handling
Sensor Control, PLC Control, Host Control.
Cimpak is built for safe operation, no guarding is required. (Location of machine may mean that guarding is required to protect operators now going into the palletizing are from vehicles and conveyors).
Pallets must be guided past the Cimpak on a powered conveyor.
Pallets must be stopped to allow labelling 1 or 2 stop positions will be required depending on the number of labels and label position.

Stand
Cimpak 300 style stand. Stand must be bolted into floor.

Max Label Width (Not Printable Area)
160mm with 152mm printhead options

Specifications and other technical information are subject to change without notice.